Plumbing Basics: What You Need for Bathtub Installation
Plumbing Basics: What You Need for Bathtub Installation
Blog Article
This article listed below about A Step-by-Step Guide to Installing a Bathtub is immensely insightful. Read it for your own benefit and decide what you think of it.
Installing a bath tub isn't specifically brain surgery, but it does call for solid plumbing, woodworking, and also in some cases, tiling abilities. Replacing an old tub with a brand-new one is additionally a moderately difficult task. If the old tub is readily easily accessible, the task can move immediately; if you have to open a wall surface to get rid of the old tub and position the new bathtub, the job is a lot harder. In either instance, the job is within a residence handyman's skills, although you will need a helper to leave the old tub as well as embeded in the new one. Make sure you have actually qualified yourself for the task and also fit trying it. Rather than employing a contractor to take control of a halfway-completed task, it is better to take into consideration utilizing one before you start. Possibilities are you may require a professional plumber to make tube connections.
This write-up will assist you install a brand-new bath tub in your shower room if you have actually currently purchased a new bathtub and don't require to transform the plan of your previous supply of water pipes.
Your tools as well as material list ought to comprise the following:
Removing Old Taps
If you need to change old faucets with new ones as a part of your installment, after that the first thing you must do is detach the water. After doing so, switch on the faucets to drain any kind of water staying in the system. The procedure of removing the existing faucets can be quite bothersome because of the limited gain access to that is commonly the instance.
Make use of a container wrench (crowsfoot spanner) or a faucet device to reverse the nut that connects the supply pipes to the faucets. Have a cloth all set for the continuing to be water that will certainly come from the pipelines. As soon as the supply pipes have been eliminated, make use of the exact same device to loosen the nut that holds the taps onto the bath/basin. You will certainly need to quit the solitary faucets from transforming during this procedure. Once the faucets have actually been eliminated, the holes in the bath/basin will have to be cleaned up of any old securing substance.
Prior to proceeding to fit the brand-new faucets, compare the pipeline links on the old faucets to the new taps. If the old faucets are longer than the new taps, after that a shank adapter is needed for the new taps to fit.
Fitting New Touches
If the tails of the new taps are plastic, after that you will certainly need a plastic port to prevent damages to the thread. One end of the connector fits on the plastic tail of the faucet and the other end provides a connection to the existent supply pipes.
If you require to fit a monobloc, after that you will certainly call for lowering couplers, which connects the 10mm pipeline of the monobloc to the typical 15mm supply pipeline.
Next, position the tap in the placing hole in the bath/basin making certain that the washers remain in place between the faucet and also the sink. Protect the faucet in place with the maker provided backnut. Once the faucet is securely in place, the supply pipes can be linked to the tails of the faucets. The taps can either be linked by using corrugated copper piping or with normal faucet connectors. The previous type must be connected to the tap finishes first, tightening just by hand. The supply pipelines can later on be linked to the other end. Tighten up both ends with a spanner after both ends have actually been connected.
Mounting the Bath tub
Making use of both wood boards under its feet, position the tub in the called for placement. The wood boards are valuable in equally spreading the weight of the tub over the location of the boards rather than concentrating all the weight onto four small factors.
The next goal is to make certain that the bathtub is leveled all round. This can be accomplished by examining the level and also readjusting the feet on the bathtub until the spirit level checks out degree.
To mount taps, fit all-time low of the outermost versatile tap connector to the proper supply pipeline by making a compression sign up with; after that do the exact same for the various other faucet.
Turn on the supply of water as well as inspect all joints and also brand-new pipework for leaks as well as tighten them if essential. Load the bath tub and additionally inspect the overflow electrical outlet and also the typical electrical outlet for leaks.
Finally, repair the bathroom paneling as explained in the manufacturer's instruction manual. Tiling and also sealing around the bathtub needs to wait until the bath tub has actually been used at least when as this will certainly resolve it into its final setting.
Planning for the Installment
First of all, the sustaining framework supplied with the bathroom should be fitted (if called for) according to the producer's directions. Next off, fit the faucets or mixer to the bath tub. When fitting the tap block, it is necessary to ensure that if the faucet features a plastic washing machine, it is fitted in between the bathroom as well as the taps. On a plastic bathroom, it is also reasonable to fit a sustaining plate under the faucets unit to prevent strain on the bathtub.
Fit the versatile faucet adapters to the bottom of both taps making use of 2 nuts and also olives (often supplied with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet opening, and after that pass the electrical outlet with the hole in the bathroom. Use the nut provided by the supplier to fit the plug-hole. Check out the plug-hole outlet for an inlet on the side for the overflow pipe.
Next, fit the end of the versatile overflow pipeline to the overflow electrical outlet. Afterwards, screw the pipeline to the overflow face which should be fitted inside the bathroom. Make sure you use every one of the provided washers.
Link the trap to the bottom of the waste outlet on the bath tub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, and screw on the catch to the outlet. Link all-time low of the overflow tube in a similar manner.The bath need to now be ready to be fitted in its last placement.
Tiling Around the Bath tub
In the location where the bath satisfies the floor tile, it is essential to secure the accompanies a silicone rubber caulking. This is necessary as the installation can relocate enough to split an inflexible seal, triggering the water to permeate the wall surface between the bath and also the tiling, bring about problems with dampness and possible leakages to the ceiling listed below.
You can choose from a variety of coloured sealers to blend in your fixtures and also installations. They are offered in tubes and also cartridges, and also are capable of securing spaces as much as a size of 3mm (1/8 inch). If you have a larger void to fill, you can load it with spins of drenched newspaper or soft rope. Keep in mind to constantly load the bathtub with water prior to sealing, to permit the movement experienced when the bathtub is in use. The sealant can crack rather early if you do not consider this movement prior to securing.
Additionally, ceramic coving or quadrant ceramic tiles can be utilized to border the bathroom or shower tray. Plastic strips of coving, which are easy to use and reduce to size, are also conveniently offered on the marketplace. It is recommended to fit the tiles utilizing waterproof or water-proof sticky as well as grout.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
We had been made aware of that article about How to Install a Bathtub from someone on a different blog. Do you know about anybody else who is truly interested in the subject? Feel free to share it. Thanks for going through it.
Schedule Service Report this page